Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Mechanical Advantages of Eddy Current Drives

Dynamatic
Dynamatic Figure 1 Eddy Current Drives

Mechanical Advantages of Eddy Current Drives

By: Dynamatic

By Jennifer Ludlum, Regional Sales Engineer

When most people discuss variable speed drives, they often talk about efficiency and harmonics. Let’s take a look at the mechanical side of variable speed drives and with an eddy current drive the benefits are significant.

Dynamatic Figure 2 Eddy Current DrivesIn an eddy current drive, the motor and driven equipment are not physically connected. The input and output shafts turn independently. The motor end is within the frame of the drive unit, and an open-ended cylinder is coupled to the motor shaft. (Figure 1) Attached to the driven equipment is the output rotor (Figure 2). This rotor has a coil that receives excitation from a small DC current to form a magnetic field. This field then transmits the torque from the motor to the driven load. (Figure 3).

Dynamatic Figure 3

The mechanical advantages of an ECD allow:

  • Start and stop equipment without regard to the motors starting and stopping limitations. The motor will run continuously at design speed but unloaded.
  • Start the motor unloaded.
    • The design promotes starting the motor under no-load condition, extending motor life
    • This results in cushioning between the drive system and load, permitting longer life for the machinery involved
    • One way this is beneficial is if you are running equipment that is subject to blockages – it avoids tripping circuits
  • If the driven equipment gets jammed/overloaded the motor shaft is unaffected.
  • The motor is always running at design speed. This provides maximum cooling to the motor helping extend the motor life.
  • Ramp-up load – Increase the load speed as slowly or quickly as needed for the process.
  • No harsh service or temperature – neither the eddy current coupling nor the controls need air conditioning. Like the motors that drive them, the variable speed electromagnetic drive unit is easily cooled with ambient air.
  • The ability for multiple starts and stops eliminates Peak Demand charges.

Other mechanical advantages:

High starting torque – intermittent availability of up to 250% of the rated motor torque. (See overload curve below)

Dynamatic overload curve

Overload Curve

  • Dynamatic® drives deliver full torque throughout the speed range (0-100%).
    • A constant torque load is characterized as one in which the torque is constant regardless of speed.
    • The horsepower requirement is directly proportional to the operating speed of the application and varies directly with speed.
    • Since torque is not a function of speed, it remains constant while the horsepower and speed vary proportionally.

With a typical life cycle of 40-60 years, Dynamatic® drives are the longest lasting variable speed drive system if they are maintained properly.

Dynamatic Eddy current drivesSimple Maintenance

Eddy current drives are maintained much like a motor. Every 6-12 months:

  • Grease bearings
  • Replace brushes, if applicable
  • Clean dust/ debris out of the enclosure

Related Articles

Related Whitepapers

Expansion Joint Expertise Improves Industrial Wastewater System Reliability

The majority of industries have wastewater treatment plants. Government agencies and local governments require these facilities to meet pretreatment requirements. Pretreatment rules were enacted to prevent…

How to Decrease Oil Changes with Bearing Isolators [Inforgraphic]

Learning how to decrease oil changes can be time- and money-saving. Oil life can be long if contamination is eliminated, which is easier said than…

Synchronous Machines Are The Optimal Choice For Heavy Industry

TECO-Westinghouse experience assures superior performance and reliability For over a century, Westinghouse has been the pacesetter in the design and production of electric machines for heavy…

Why FLEXXORs Are Designed Differently

J. Hilbert Anderson, President of Coupling Corporation of America, discusses some of the reasons why FLEXXORs are designed differently from all other flexible couplings, and…

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact