Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Tips to Prepare Your Pumps for Cold Weather

KSB

Tips to Prepare Your Pumps for Cold Weather

By: KSB

Winter is coming! Are your pumps ready? Here are the steps you should take to ensure your pumps are prepared to operate during extremely cold weather.

If you work in the Oil Sands, you’re no stranger to tough, remote conditions — and neither is your equipment. However, harsh winters can be especially hard on slurry systems – especially if you haven’t properly winterized your pumps.

With so much moisture present during operation, slurry pumps become notably vulnerable to damage in cold weather. Frozen water in your pump system can lead to crippling issues ranging from improper functioning and premature parts failure all the way to more costly damage caused by freeze-and-thaw issues or thermal shock.

The good news is — with a little preparation and careful operation — your system can be winterized without trouble. Here are five steps to help you maintain your system in extreme cold conditions:

1. Protect your pipes and pumps from the elements.
Since mechanical seals and bearings are particularly vulnerable to damage while operating in freezing conditions, protect them by heat tracing and wrapping your seal water piping. A heated shelter is ideal, but not every slurry pump in the Oil Sands has this luxury. If this is not practical, do not stop the slurry flow! Instead, find a way to protect your pump from the elements and use an appropriate heat source to raise the temperature of the bearing assembly, lubricating oil, and pump casing before starting it up. Look to your local codes to determine the most suitable heat source for the job.

2. Prevent freezing during shutdowns.
If you’re shutting your unit down in sub-zero conditions, make sure it’s completely free of water so it doesn’t freeze, expand, and result in damage. Some pumps are designed for periodical stops with built-in plugs in the shell base. However, other systems require you to remove the system piping and pump out the casing. Looking for another option? Install a dump valve in the lowest point of the piping system and use it. Whichever method you choose, don’t forget about the stuffing box and lines.

3. Check your oil.
Your pump’s bearings will need extra attention during the winter months. That’s because any moisture or condensation inside the bearing races will quickly turn to ice, preventing smooth movement in the assembly and resulting in damage and untimely failure. Before cold weather arrives, change your CBA oil and check the viscosity or “weight” of the oil against the coldest expected air temperature to ensure the oil is correct for the conditions. Depending on your bearing size, a synthetic oil may be recommended. Unlike traditional mineral oils, the pour point of synthetics is designed to maintain effective lubrication at low temperatures.

4. Prepare your pneumatics and v-drives.
If your isolation valves are pneumatically actuated, make sure your air dryer is functioning optimally. For v-drives, consider installing new belts for the winter so you don’t have to deal with replacing them when it’s negative 40-degrees.

5. Operate with care.
When operating your slurry system in a wintery environment, take care to properly start up and oversee your system. Your pump casing should always be brought up to operating temperature gradually, either with process flow or external heat, to prevent thermal shock. The stuffing box also needs a constant supply of water, which may need to be insulated or heated, and flush water must be drained to prevent ice buildup.

These tips should help you keep your slurry system in working order through the winter and beyond. For those seeking to upgrade their system or purchase new pumps for their line, it’s also important to keep in mind that pumps and slurry systems can be designed with harsh environments — and severe temperature fluctuations — in mind.

By working with an expert who is familiar with your environment and your needs, you can rely on a slurry system that’s prepared for anything — even a frigid winter in the Canadian Oil Sands!

Looking for assistance with your slurry system’s winterization? Give GIW a call! Our expert technicians in Fort McMurray are available to help even the most remote customers maintain their pumps and systems.

GIW FORT MCMURRAY SERVICE CENTER | GIW Industries, Inc. (A KSB Company)
220 MacLennan Cr., Fort McMurray, AB, Canada T9H4E8
Phone: +1 780 713 3457
Fax: +1 780 713 3458
Mobile: +1 780 370 5431

Related Articles

Related Whitepapers

Expansion Joint Expertise Improves Industrial Wastewater System Reliability

The majority of industries have wastewater treatment plants. Government agencies and local governments require these facilities to meet pretreatment requirements. Pretreatment rules were enacted to prevent…

How to Decrease Oil Changes with Bearing Isolators [Inforgraphic]

Learning how to decrease oil changes can be time- and money-saving. Oil life can be long if contamination is eliminated, which is easier said than…

Synchronous Machines Are The Optimal Choice For Heavy Industry

TECO-Westinghouse experience assures superior performance and reliability For over a century, Westinghouse has been the pacesetter in the design and production of electric machines for heavy…

Why FLEXXORs Are Designed Differently

J. Hilbert Anderson, President of Coupling Corporation of America, discusses some of the reasons why FLEXXORs are designed differently from all other flexible couplings, and…

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact