Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Proco Check Valves Provide Better Diffusion Value on Sea Floor

Proco Products

Proco Check Valves Provide Better Diffusion Value on Sea Floor

Project: Marine Wastewater Outfall Diffusion

Location: Istanbul, Turkey

Owner: Water Authority of Istanbul

Designer: Marine Consultants Group


Final assembly prior to operation

The Water Authority of Istanbul, which owns a biological wastewater treatment plant, serves a population of about 15 million people in the city of Istanbul, Turkey. To meet stricter environmental regulations, the Water Authority approached Marine Consultants Group (MCG) in the spring of 2017 to find a suitable product to provide adequate diffusion for their marine wastewater outfall. Marine Consultant Group worked with Proco to design and engineer duckbill diffusers to accommodate outfall sewage from the treatment plant through an 87 inch diameter steel pipe. The pipe extends 1.35 miles (2230 meters) along the bottom of the ocean and discharges at about 154 feet below sea level.

check valves provide diffusion

The 87-in. manifold pipe prepared for submersion

There were several challenges Proco needed to keep in mind for this project. One concern was that diffusers and duckbill check valves might be damages by passing marine vessels. To address this concern, Proco needed to determine the appropriate diffuser length, which in this project was about 741.5 feet at the farthest end of the 1.5 miles run on outfall pipe. Previously, engineers and contractors were often required to blind flange some of the ports so that they would be functional with less flow rates and opened to allow for future maximum flow rates. Maximum flow was calculated to handle requirements with a 20-year future outfall rate. However, the present flow rate will not be functioning at maximum output, as a result, Proco and MCG needed to design appropriately sized check valves to alleviate this concern.



Cranes setting the ProFlex assembly on the manifold

The Marine Consultant Group recommended that the Water Authority use the Proco ProFlex™ 710 duckbill check valves for this project, and each port discharge was equipped with two, 10-inch diameter (250mm) duckbill check valves. Duckbill valves are frequently used to prevent backflow in deep marine outfall/diffuser projects. The Proco ProFlex™ 710 duckbill check valves provided several advantages for this marine outfall. First, there was no need to blind cap some of the ports during the first years of operations. Secondly, the use of the Proco ProFlex™ 710 duckbill check valves eliminates the need to blind flange ports since the lines can operate with full efficiency from the initial startup, which decreases maintenance and reduces diver time to add additional valves in the future.

Another benefit of using duckbill check valves for this project was to prevent saline intrusion  into the line when there is not inlet pressure. Different head pressures between seat water and discharge water cause sea water to enter the line when there is low head pressure or when there is no inlet flow. If this backflow is not prevented, the ports may be blocked or plugged, and marine life can enter the lines. As a result, the calculated and engineered dilution ratios will then not be achieved. Finally, duckbill check valves increase the jet velocity and provide a better dilution value than traditional flap gates, even with low flow rates.

An example of a sized diffuser flow rates

In addition to these benefits, the Proco ProFlex™ Style 710 duckbill check valves’ highly engineered elastomer maintains its memory after a long period of staying open or staying in a closed position. One of the biggest advantages of the elastomeric valves is that they are 100 percent barnacle and Algae resistant, which is an important feature for a salt water project. Proco’s engineering team also provided full assistance with supplying the head loss calculations.


Following the installation of the Proco ProFlex™ Style 710 duckbill check valves, the finished assembly was charged with air to allow buoyancy and was then dragged into a determined position and allowed to drop to the seafloor. This allowed the Proco 710 valves to become operational and allow the appropriate outfall diffusion through each of the 46 valves. The system has been a fully functional success for the region, and Proco continues to offer assistance and engineering expertise on systems comparable to this on a globally active basis.

Related Articles

Related Whitepapers

Expansion Joint Expertise Improves Industrial Wastewater System Reliability

The majority of industries have wastewater treatment plants. Government agencies and local governments require these facilities to meet pretreatment requirements. Pretreatment rules were enacted to prevent…

How to Decrease Oil Changes with Bearing Isolators [Inforgraphic]

Learning how to decrease oil changes can be time- and money-saving. Oil life can be long if contamination is eliminated, which is easier said than…

Synchronous Machines Are The Optimal Choice For Heavy Industry

TECO-Westinghouse experience assures superior performance and reliability For over a century, Westinghouse has been the pacesetter in the design and production of electric machines for heavy…

Why FLEXXORs Are Designed Differently

J. Hilbert Anderson, President of Coupling Corporation of America, discusses some of the reasons why FLEXXORs are designed differently from all other flexible couplings, and…


Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community

By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact