Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Understanding The 5 Causes of Bearing Damage in Electric Motors

Aegis
Aegis 5 Sources of Bearing Damage in Electric Motors

Understanding The 5 Causes of Bearing Damage in Electric Motors

By: Aegis

This article is mainly about electrical bearing damage, there are plenty of other sources of damage and failure modes for motor bearings. Although there are several guides and schools of thought out there, Aegis focuses on one set of five sources of damage.  The following is adapted from an article by SKF called 5 Most Common Causes of Bearing Failure in Electric Motors and What to Do About Them.

Listed in no particular order, they are:

Electrical Erosion

Regular readers of this blog won’t be surprised to see this one on the list. Electric current, typically a side effect of variable frequency drive control, passes through the bearings. The end result is bearing fluting (image at right) and failure. This can be mitigated in several ways. Our preferred method – this being the AEGIS® blog – is to install an AEGIS Shaft Grounding Ring on motors under 100 hp/75 kW and an AEGIS ring and an insulated or hybrid bearing at the opposite end. Other approaches include two insulated bearings and an insulated coupling for the driven equipment or a sinewave filter capable of converting the drive’s current and voltage waveforms to sinewaves. These solutions are effective but more expensive than shaft grounding.

Inadequate lubrication and contamination

Bearings spin at high speed, and without adequate lubrication, you will end up with metal-metal contact, causing wear, heating, and possible contamination of the lubricant. The first preventive measure is to check that the regreasing lubricant type, volume, and interval are appropriate. If there is contamination, check the seals. In some cases, a more-viscous lubricant may be needed. (It should be noted that over-greasing can also cause problems.)

Improper installation and setup

This can cause several types of damage. Common mistakes include using a hammer to couple the shaft to the load (which can cause true brinelling), misalignment, imbalance, applying excessive belt tension, and errors in mounting, causing overloading. To avoid these errors, always follow the recommended installation procedures and use quality instruments to determine alignment, tension, etc.

Insufficient load

Bearings need a minimum load to function properly. Inadequate load can be as damaging as excessive load. Damage from insufficient load appears as smearing on the rolling elements and races. This is especially important with cylindrical roller bearings since they are designed for larger loads. (This does not apply to preloaded bearings.)

It is worth pointing out that these damage modes are not mutually exclusive and may interact with each other. For instance, insufficient load may make electrical erosion happen faster (by allowing shaft voltage to build up higher before discharge occurs). Electrical erosion also contributes to lubricant contamination because the arcing chemically degrade the grease and releases microscopic metal particles into the lubricant.

Aegis 5 Sources of Bearing Damage in Electric MotorsVibration

Motor bearings can be damaged by vibration, both during transportation and even while sitting in storage. The vibrations create marks in the bearing races called false brinelling (shown above; which somewhat resembles fluting). This can be prevented during transport by locking the shaft axially with a flat piece of steel bent into a “U” shape while preloading the non-drive end and then radially locking the drive end with a strap. To prevent vibrational damage during storage, you can turn the shaft periodically so any vibrational contact is spread across the bearing surface (rather than building up into false brinelling).

Why Stay In Touch With Your Bearing Manufacturers
If you’d like to learn more, most major bearing manufacturers – and several bearing distributors – have resources available on common causes, appearance, and prevention of bearing damage.

As for electrical bearing damage, AEGIS Shaft Grounding Rings have a 2-year extended warranty against bearing fluting damage. No other form of shaft grounding offers a warranty like this.

Related Articles

Related Whitepapers

Expansion Joint Expertise Improves Industrial Wastewater System Reliability

The majority of industries have wastewater treatment plants. Government agencies and local governments require these facilities to meet pretreatment requirements. Pretreatment rules were enacted to prevent…

How to Decrease Oil Changes with Bearing Isolators [Inforgraphic]

Learning how to decrease oil changes can be time- and money-saving. Oil life can be long if contamination is eliminated, which is easier said than…

Synchronous Machines Are The Optimal Choice For Heavy Industry

TECO-Westinghouse experience assures superior performance and reliability For over a century, Westinghouse has been the pacesetter in the design and production of electric machines for heavy…

Why FLEXXORs Are Designed Differently

J. Hilbert Anderson, President of Coupling Corporation of America, discusses some of the reasons why FLEXXORs are designed differently from all other flexible couplings, and…

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact