Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Spherical Valves for a Wide Variety of Pumps

Industry Topics

Spherical Valves for a Wide Variety of Pumps

Reciprocating pumps in the current market are often operating at higher RPM and varying suction pressures as determined by consumer demand, system limitations and to improve process efficiency. This requires the use of a valve that can operate efficiently under demanding conditions found in manufacturing sectors and is still able to perform adequately under changing conditions such as those seen in the oilfield. TPCI offers 3 valve configurations to meet this need:

· A low suction pressure (2 POSIVA) configuration for use with less than adequate suction conditions.

· A standard suction pressure (4 POSIVA) configuration for use under normal suction conditions.

· And a high speed (6 POSIVA) configuration for improved efficiency during operation at higher RPMs.

Additional configurations can be accommodated to suit the specific suction or discharge requirements of your application.

POSIVA

POSIVA is an acronym for pounds per square inch of valve area. This refers to the spring load applied to the valve member when the valve is in the closed position. POSIVA is directly proportional to the cracking pressure of the valve and is a significant factor for valve operation in relation to variance in pressure and pump RPM in different systems. One size does not always fit all.

Low Suction Pressure Systems

In systems with less than optimal suction pressure, it is common for the valve to open later than needed for optimal performance during the suction cycle. This opening delay reduces the volume of fluid transferred into and then out of the pump. The end result is an overall decrease in the volumetric efficiency of the pump. Under these conditions it is important to mitigate the impact of the slow opening valve. TPCI offers a single spring, lightly loaded configuration to improve valve performance in low suction pressure systems. By reducing the POSIVA to 2, excess spring pressure in the valve is removed so the valve is able to open earlier. This minimizes volumetric loss due to low suction pressure and improves volumetric efficiency.

Normal RPM, Normal Suction Pressure Systems

Reciprocating pump operation under OEM recommended piping and suction conditions are typically of no consequence. TPCI offers a single spring standard load configuration for use in applications where suction pressure is adequate. Under these ideal conditions a standard spring load of 4 POSIVA is sufficient for optimal performance.

High RPM Operation

In high RPM applications, the extreme cycle times do not typically impact the pump at the suction end. What typically occurs is a delay in the closing of the discharge valve in relation to the position of the plunger. This closing delay results in a momentary decrease in the discharge pressure for the given chamber and reduces overall fluid transfer. The occurrence is directly proportional to pump RPM and the viscosity of the medium being transferred. To combat this effect, TPCI offers a dual spring configuration in which the POSIVA has been increased to 6. The increase in the spring load increases the closing time of the valve and again results in better volumetric efficiency during high RPM operation.

Triangle Pump Components Introduces Low-Cost, High-Efficiency Spherical Valves

The WG Sphera series valves are built to last. The cage, seat and valve members are constructed from 316 and hardened 17-4 stainless steel for use in a wide array of fluid media. The springs are an Inconel alloy which increases the operational longevity of the valve. The result is fewer maintenance intervals, longer production intervals and greater overall output.

Additionally, an efficient, low-cost valve pays off at the time of purchase and over the lifetime of the pump. The newly introduced WG Sphera series of stem-guided, optional single or dual spring, spherical profile pump valves from Triangle Pump Components Inc. (TPCI) are a robust, efficient and reliable solution for pump maintenance at an affordable cost.

Plus, owners and end users can reduce power end wear as a result of the smoother flow through this valve. The power end parts are considerably more expensive than the fluid end and are a lot more difficult to replace. By easing the flow of fluid through the valves, there is less resistance into the power end, thereby reducing wear on the bearings, crankshaft, and connecting rods. An additional benefit is the lessening of power consumption costs (savings in electricity usage).

Figure 1. The individual components of the TPCI WG Sphera series spherical valve (left) and a fully assembled version (right) showing the large spring option. Source: Triangle Pump Components Inc.The individual components of the TPCI WG Sphera series spherical valve (left) and a fully assembled version (right) showing the large spring option. 

Positive Experiences

Initial customer experiences with the new spherical valves have been positive, and demonstrate durability and efficiency.

In one test, a customer installed the WG Sphera metal-to-metal 10 and 11 series 316 stainless steel spherical valves in a National J-165L plunger pump using 2.75 in. plungers. The pump produced over 3,147 B/D of fresh water at close to 240 rpm, operating every day for 18 months. After this period, the valves were removed and inspected — both the suction and discharge valves had sufficient durability to run much longer. The customer normally uses stainless steel plate valves with Delrin discs, which need service after only nine to ten months of operation. The spherical valves provided more than double the lifetime of the previous valves.

In another test, a customer installed WG Sphera 10 series 316 stainless steel spherical valves with an inner Inconel 600 spring in a Weatherford® W165-5L triplex plunger pump using 2.75 in. plungers. The pump is used for oilfield salt water disposal and operates at 350 rpm with a temperature range between 60° F to 100° F. When the valves were removed and inspected after nine months of service, the wear was minimal considering the harsh conditions. Previously used abrasion-resistant valves had a typical lifespan of just three to four months.

A current test involves the installation of the WG Sphera metal-to-metal 8 series 17-4 stainless steel spherical valves in a National 165T-5M plunger pump. It is producing 2,500 to 2,700 B/D of salt water disposal with a pumping pressure of 1,750 psi. The valves, inspected after six months of operation, “looked great” according to the customer and will be checked again in another 6 months. Its predecessors lasted only three to four months before showing extensive stem wear.

The new spherical valves from Triangle Pump Components Inc. provide a low-cost, robust solution for a wide range of pump systems from most manufacturers. To find out more about TPCI’s new WG Sphera series of stem-guided, optional single or dual spring, spherical profile pump valves, visit their website.

Related Articles

Sulzer Cost effective sustainable fuel production

Cost effective sustainable fuel production

Benchmarking Market Report highlights cost-leadership of Sulzer Chemtech BioFlux Process Technology for Renewable Fuels production BioFlux® process technology for renewable fuel…

Related Whitepapers

Expansion Joint Expertise Improves Industrial Wastewater System Reliability

The majority of industries have wastewater treatment plants. Government agencies and local governments require these facilities to meet pretreatment requirements. Pretreatment rules were enacted to prevent…

How to Decrease Oil Changes with Bearing Isolators [Inforgraphic]

Learning how to decrease oil changes can be time- and money-saving. Oil life can be long if contamination is eliminated, which is easier said than…

Synchronous Machines Are The Optimal Choice For Heavy Industry

TECO-Westinghouse experience assures superior performance and reliability For over a century, Westinghouse has been the pacesetter in the design and production of electric machines for heavy…

Why FLEXXORs Are Designed Differently

J. Hilbert Anderson, President of Coupling Corporation of America, discusses some of the reasons why FLEXXORs are designed differently from all other flexible couplings, and…

Comments

One response to “Spherical Valves for a Wide Variety of Pumps”

  1. Insightful article. It is really very important to choose the right valve. Thanks for sharing. 🙂

Leave a Reply

Your email address will not be published. Required fields are marked *

Join the #PumpTalk Community


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact